Category Archives: Shim Washers

Shim Washers as Spacers: Precision Spacing in Mechanical Assemblies

Shim washers are ultra-thin, flat rings engineered to tight thickness tolerances that act as precision spacers in mechanical assemblies. Unlike standard washers that primarily spread fastener loads, shim washers fine-tune clearances, align moving parts, and eliminate unwanted play between components.

What Sets Shim Washers Apart

  • Tight Thickness Tolerances. Standard washers vary noticeably in thickness from piece to piece, whereas shim washers are stamped or machined to exact fractions of a millimetre.
  • Flatness and Parallel Faces. Manufacturers craft them with smooth edges and parallel surfaces to prevent uneven tilting or wobbling when stacked.
  • Stackable Design. You can combine multiple thin shim washers of varying thicknesses to hit an exact custom gap without custom machining.

Key Applications as Spacers

  • Eliminating Axial Play. Placed along shafts or rods, they take up microscopic gaps so gears, pulleys, and bearings do not slide back and forth.
  • Bearing Preload and Alignment. Technicians use them to set exact bearing preloads and ensure rotating parts line up squarely to prevent premature wear.
  • Tolerance Compensation. In multi-part assemblies, small manufacturing variations add up. Adding a shim washer restores the exact target clearance.
  • Levelling and Squaring. Placed under mounting brackets or screw heads, they level uneven surfaces in tight spaces.

💡 Best Practices When Using Shim Washers

  • Avoid Over-Stacking. Stacking too many ultra-thin shims increases the chance of surface slippage and reduces joint rigidity. Always use the fewest number of shims possible to reach your target thickness.
  • Place Thicker Shims Outside. If you must stack multiple shims, sandwich the thinnest shims between thicker ones to protect them from tearing or deforming.
  • Check Inner and Outer Diameters. Match the inner diameter closely to the shaft or bolt size so the shim stays centred and does not shift under vibration.
  • Clean Surfaces First. Even a tiny speck of dirt or grease can throw off the precision spacing a shim washer is meant to achieve.

The Core Anatomy of a DIN 988 Shim Washers

What is the DIN 988 Standard?

DIN 988 is a German technical standard that outlines the strict dimensions, tolerances, and materials for metric shim rings (fit washers) and supporting rings. Published to establish consistency across manufacturing, the standard dictates how these washers are produced to ensure exact spacing and precise mechanical adjustments.

While standard flat washers are designed simply to distribute the clamping force of a bolt, DIN 988 Shims are specifically designed to take up axial play, control end float, and accurately preload bearings.

The Core Anatomy of a DIN 988 Shim

A DIN 988 shim washer is designated by three strict metric measurements:

  1. Inside Diameter (d₁): Designed to fit snugly over a shaft or fastener location. Nominal sizes range widely, from tiny M3 configurations up to massive M170 industrial applications.
  2. Outside Diameter (d₂): Defines the total outer surface area, providing structured support against the adjacent housing or bearing face.
  3. Thickness (h): The absolute core feature of the shim. Thicknesses are precisely controlled and generally range anywhere from an ultra-thin 0.1mm up to 2.0mm or more.

Shim Rings vs. Supporting Rings

The DIN 988 standard actually categorises components into two distinct types based on the mechanical problem they solve:

  • Shim Rings (PS Series): These have perfectly smooth contact faces. Their primary job is to bridge small physical gaps, remove axial play, and stop components from sliding back and forth along a shaft. They are typically stamped from carbon spring steel or stainless steel.
  • Supporting Rings (SS Series): These are built to handle heavier mechanical abuse. They are placed against rounded or chamfered component edges to prevent structural deformation caused by severe axial forces. They feature higher material hardness (440 to 500 HV) and are typically machined with precise ground side faces, making them more expensive than standard shim rings.

Common Industrial Applications

You will find DIN 988 shims anywhere precision rotating motion is required. A few crucial use cases include:

  • Gearboxes & Transmissions: Keeping gears perfectly aligned on their shafts to prevent premature tooth wear.
  • Bearing Assemblies: Compensating for minor tolerances in bearing seats (e.g., standard crankshaft bearings like the 6305) to eliminate end-play.
  • Electric Motors & Pumps: Controlling the magnetic centering and end-float of rotating armatures.
  • Retaining Ring Support: Placed directly ahead of a circlip or snap ring to provide a perfectly square, flat surface for the retaining clip to bear against.

Please contact us today if you require assistance finding the right Shim Washer.

Eliminate Play. Perfect Your Fit. Precision Shim Washers.

When a fraction of a millimetre makes the difference between flawless operation and catastrophic wear, you cannot afford to compromise. Our premium-grade Shim Washers are engineered to deliver micro-precise spacing, eliminating unwanted axial play and ensuring perfect component alignment in your most critical assemblies.

⚙️ Applications Across Industries

Our shim washers are trusted by engineers, machinists, and technicians across demanding sectors:

  • Automotive & Motorsport: Preloading bearings, setting gear backlashes, and adjusting suspension geometry.
  • Aerospace & Defense: High-tolerance spacing in environments where component failure is not an option.
  • Manufacturing & Robotics: Aligning automated tooling, ball screws, and rotating shafts.
  • Power Transmission: Precision spacing within gearboxes, pumps, and electric actuators.

🛡️ Built for Tolerance. Engineered for Performance.

Whether you are eliminating end-play in a high-speed electric motor, calibrating a automotive differential, or maintaining heavy industrial machinery, our shims provide the exact spacing you need.

FeatureSpecifications & Advantages
Micro-Precise ThicknessesAvailable from 0.1mm to 3mm for ultra-fine adjustments.
Premium Material GradingChoice of A2 Stainless Steel or Carbon Spring Steel
Burr-Free EdgesPrecision stamped and deburred to guarantee completely flat seating and uniform load distribution.
Comprehensive Size RangeInternal Diameters (ID) and External Diameters (OD) matching all standard metric fastener sizes, plus custom dimensions on request.

🏁 Why Top Mechanics Choose Our Shims

  • Micro-Adjustment Versatility: Available in ultra-fine increments so you can stack or single-source the perfect clearance.
  • Zero-Burr Stamping: Every shim is precision-stamped and completely deburred. You get perfectly flat seating and uniform load distribution every single time.
  • Standard Automotive Sizing: Perfect fitments for standard metric and imperial shaft, spindle, and fastener diameters.

📦 Ready-to-Ship Kits

  • Pre-Packed Assortment Kits: Keep a comprehensive range of thicknesses on hand. Our heavy-duty organizer kits ensure you always have the right shim when unexpected downtime strikes.

⚡ Built for the Trade: The Online Checkout Advantage

  • Real-Time Stock Levels: See exactly what is sitting on our shelves before you hit buy—no ghost inventory, no unexpected backorders.
  • Search by Dimensions: Don’t waste time scrolling. Filter instantly by Inner Diameter (ID), Outer Diameter (OD), or Thickness to find your match in seconds.
  • Next-Day Workshop Delivery: Order before 2pm Monday - Friday (UK MAINLAND ONLY) for guaranteed next-working-day dispatch directly to your garage.

UK Stainless Steel Shim Washers – Shop Online

We carry one of the largest ranges of Stainless Steel Shim Washers – produced from high quality A2 Stainless Steel.

Shim Washers are great when you need to fill a gap to prevent leaks or stop other parts of a machine loosening and rattling around.

Where can I buy Stainless Steel Shim Washers?

You can buy them directly through our online store – please use the link provided below.